Use the TeraFlex JL / JT: High Steer Front Track Bar Axle Bracket Kit to correct bump steer and eliminate other front-end issues on JL / JT Wrangler/Unlimited models with 3.5-6" lifts and a High Steer System. Requires additional components.
The Tera60 HD Front Axle Assembly w/ Locking Hub includes SlimLock Hub Kit, Super 60 bearings, inner and outer axle shafts, knuckle assembly, ball joints, brakes, and sensors. Add your choice of ring & pinion gear ratio, locker, and carrier.
TeraFlex HD Front Axle Housings are perfect for replacing bent, broken, or damaged axles in JL Wrangler/Unlimited and JT Gladiator vehicles including Rubicon models. Can also be used as a direct bolt-on upgrade for Jeep owners looking to beef up the stock axles' weak areas.
Tera60 HD Front Axle Housings are the ultimate upgrade for JL and JT models requiring maximum suspension up travel and compression. Compatible with all Super 60 gear ratios for extreme duty applications requiring additional ring and pinion strength.
Teraflex heavy-duty axle housings feature smooth profile surfaces, axle tubes, all necessary mount brackets, control arm bushings, forged inner knuckles, and more!
* DESIGNED FOR USE WITH COILOVER SUSPENSION *
Features:
Sealed SlimLock Locking Hub Assembly for long-term maintenance-free dependability Coilover Brackets 3.25'' O.D. x 0.375'' wall DOM axle tube for superior strength vs. weight 70'' WMS-WMS and 8x6.5'' wheel bolt pattern Fixed spindle mount hub assembly Tera60 specific high-pinion front axle housing design Includes 1350 series pinion yoke 35-spline inner axle shafts and outer stub shafts Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing Oversized outer pinion bearing handles increased torque and high-load conditions High-capacity housing holds maximum amount of oil Asymmetric housing design for extra-long tube side strength Pre-installed inner axle seals HD forged inner knuckles w/ greater upper and lower section strength Ductile cast iron housing w/ increased rib gussets HD ductile iron differential cover Smooth radius bottom design to glide over rocks and obstacles Integrated lower control arm skid plates High-flow oil passages Reinforced front track bar mount (ties into spring pad) for greater strength UV protected triple-stage powder coat for corrosion resistance 1/4''-thick CNC laser cut axle brackets for extreme strength Integrating the front upper control arm mounts into the housing increases up travel an additional 2'' compared to other aftermarket Dana 60 axles Pre-installed upper control arm bushings Proper pinion angle and raised track bar bracket for lifted JL/JT applications Pre-tapped hole on spring perch for bump stop extensions Pre-drilled holes for limit straps and lower spring retainers Retains all JL/JT ESP, ABS, and speedometer sensor capability 100% engineered, designed, and built in the USA w/ new components
Specifications:
WMS-WMS: 70'' Axle Tube: 3.25'' x 0.375'' Wheel Bolt Pattern: 8x6.5'' 8 Hours (No R&P) / 6 Hours (Geared) install time
Below is a list of Requirements & Recommendations as budget and build preference allows:
HD Forged Drag Link Kit (0-6'' Lift) REQUIRES adjustable control arms for caster angle adjustments.
JL Options:
Long Control Arm & Bracket Kit: 8-Arm (3-6'' Lift) (Alpine IR: JL2: 1310512 or JL4: 1310510) (Alpine: JL2: 1316012 or JL4: 1316010). Short Control Arm Kit: 8-Arm (0-4.5'' Lift) (Alpine IR: 1416510 or Alpine: 1416610).
JT Options:
Short Control Arm Kit: 8-Arm (0-4.5'' Lift) (Alpine IR: 1417550 or Alpine: 1417500).
Product Specifications
- Axle Type: Dana 60
- Bolt Pattern: 8x6.5
- Spline Count: 35
- Tubing Diameter: 3.25in
- Width: 70in
