null
Exclusive Discounts! Add To Cart For Best Pricing!

Chevrolet Colorado Lift Kit Guide

Leveling kits, Trail Boss lifts, ZR2 kits that keep the Multimatic DSSV shocks, and fender-flare routes to 35s for the 2023+ Chevrolet Colorado, with the trim differences that decide which kit fits your truck.

Last Updated: Oct 4, 2026Vehicle: Chevrolet Colorado (2023+)Topic: Lift KitsBy Austin, owner of Offroad Source

Quick Answer

Colorado lift kits are trim-specific. The Trail Boss comes with a 2 in factory lift and the ZR2 with a 3 in factory lift and Multimatic DSSV dampers, and both use their own kits; a kit built for the Trail Boss won't fit a WT, LT or Z71, and ZR2 kits won't fit a Trail Boss. A front strut spacer level (about 1 in) is the simplest step on a Trail Boss or ZR2. For 35s, ZR2 owners can either add a 3 in kit that keeps the DSSV shocks or use AEV's HighMark fender flares, which clear 35s with only small spacers. Lift height alone never guarantees a tire size; wheel offset and tire width matter just as much.

1. What You Need to Know First

The third-generation Colorado (2023 and newer) is a crew cab, short box truck with independent front suspension on coil-over struts and a solid rear axle on leaf springs. Chevrolet builds it in five off-road-relevant configurations, and three of them sit at different heights from the factory:

  • WT and LT: standard suspension, about 7.9 in of ground clearance (2023 figures).
  • Z71: standard-height suspension with off-road equipment, about 8.9 in of clearance.
  • Trail Boss: a 2 in factory lift and a front track about 3 in wider than the WT and LT, with about 9.5 in of clearance.
  • ZR2: a 3 in factory lift, wider stance, Multimatic DSSV dampers, cast-iron control arms and front and rear electronic lockers, with about 10.7 in of clearance.
  • ZR2 Bison: a ZR2 with AEV bumpers and fender flares, boron steel skid plates, jounce control dampers and factory 35s, rated at 12.2 in of clearance.

Because the Trail Boss and ZR2 use different suspension parts than the standard trucks, lift kit makers build separate kits for each. Always match the kit to your exact trim, not just "2023+ Colorado."

2. Which Option Is Right for You?

Level Only

Best for:
  • Removing factory rake
  • A slightly bigger tire
  • Keeping factory ride
  • Lowest cost, bolt-on
Typical liftAbout 1 in front

Trail Boss Lift

Best for:
  • Trail Boss owners chasing 33s to 35s
  • New upper control arms
  • Matching rear height
  • Weekend trails
Typical liftAbout 3 in over factory

ZR2 to 35s

Best for:
  • Keeping DSSV dampers
  • 35 in tires
  • Lift kit or fender flares
  • Serious trail use
Typical route3 in kit or HighMark flares

3. Lift Options Compared

These are examples from manufacturer listings for 2023+ Colorados, not a complete list. Kit heights are measured over each trim's factory height.

OptionFitsWhat It DoesTire Notes (manufacturer)
Front strut spacer level, about 1 inTrail Boss and ZR2 (check the listing)Spacer on the factory strut; rear stays stockModest upgrade, such as 285/75R17 on a 17x8; trimming may be required
3 in Trail Boss liftTrail Boss 4WD only, not WT, LT, Z71 or ZR2Fabricated upper control arms, top and preload spacers, rear shocksUp to 35x11.5 on 17x8.5 or 17x9 with 5.5 in backspacing; trimming may be required
2 to 3.5 in ZR2 liftZR2 4WD onlyUpper control arms, strut spacers and rear blocks; keeps the factory DSSV shocks35x12.5 on 17x8.5 or 17x9 with 5 in backspacing; trimming may be required
AEV HighMark fender flares2023+ ZR2Taller flares with 1/2 in coil spacer and rear spring spacer; front fenders are cut33 to 35 in; AEV recommends 17x8.5 with +12 offset

A lift height doesn't guarantee a tire fits. Tire width, wheel backspacing and how far the suspension flexes still decide whether you rub; see the Tire Size Guide and Wheel Fitment Guide.

Shop Lift Kits → Shop Leveling Kits →

4. WT/LT vs Z71 vs Trail Boss vs ZR2 vs Bison

WT and LT

These trucks sit lowest and have the narrowest track. Kits built for the Trail Boss specifically say they won't fit standard trims, so look for a leveling or lift kit that lists your trim and drivetrain (2WD or 4WD). Most owners of these trucks who want a big tire and lifted stance find it simpler to start with a Trail Boss.

Z71

The Z71 sits at standard height and doesn't share the Trail Boss's lifted, wide-track suspension, so Trail Boss kits don't fit it either. Use kits listed for the Z71.

Trail Boss

The Trail Boss already has 2 in of factory lift and a wider front track. A strut spacer level adds about another inch up front, and dedicated Trail Boss lifts use new upper control arms to add about 3 in front and rear.

ZR2

The ZR2's Multimatic DSSV dampers are a big part of how it rides, so most owners want to keep them. Spacer-style kits built for the ZR2 retain the factory DSSV shocks. The other route, which AEV uses for its ZR2 conversions, is to skip a traditional lift and use HighMark fender flares to make room for 35s while keeping factory geometry.

ZR2 Bison

The Bison comes from the factory on 35 in tires (LT315/70R17), AEV fender flares and jounce control dampers. Most Bison owners don't need a lift for tire clearance; check that any kit specifically lists the Bison before buying, since the factory flares, bumpers and skid plates differ from a standard ZR2.

5. How a Lift Changes Your Colorado

Strut Spacers

A spacer on top of the factory front strut raises the front without changing the shock or spring. It's simple and keeps the factory ride, but it also increases the angle of the front CV axles and lowers how much droop is left before the suspension tops out.

Control Arms

As the front is lifted, the factory upper control arms run out of ball joint angle and camber and caster adjustment. Taller Colorado kits include fabricated upper control arms with upgraded ball joints to keep alignment in spec.

Rear Height

The rear axle rides on leaf springs. Leveling kits leave the rear alone; full lifts use blocks, spring spacers or new shocks so the truck sits level or with slight rake.

Clearance vs Lift

Lifting isn't the only way to clear bigger tires. On the ZR2, AEV's HighMark flares open up the wheel opening so 35s fit with only small spacers. Lower-offset wheels can also move the tire away from the inner liner, but they push it toward the fender.

Gearing

Taller tires make any truck feel slower and change shift points. The right setup depends on your engine output, axle ratio and tire size, so call us before you commit to a regear.

6. Supporting Parts You May Need

Upper Control ArmsRestore alignment range on taller lifts.
Rear Blocks or SpacersMatch rear height to the front.
ShocksRear shocks sized for the new height.
WheelsBackspacing matched to the kit.
AlignmentRequired after any lift or level.
Speedometer CalibrationCorrect speed after bigger tires.

Shop Suspension Components →

7. Common Mistakes

  • Buying a "2023+ Colorado" kit without checking trim. Trail Boss, ZR2 and standard-trim kits are not interchangeable.
  • Throwing away the ZR2's DSSV shocks. Choose a kit that retains them unless you have a reason to replace them.
  • Ignoring wheel backspacing. Kit makers list specific wheel specs for their tire sizes.
  • Assuming no trimming. Even with a kit, manufacturers note trimming may be required for the largest tires.
  • Skipping the alignment and headlight aim. Both change when the truck sits higher.

8. Common Owner Configurations

Trail Boss, mild

  1. About 1 in front strut spacer leveling kit
  2. Slightly larger all-terrain tire
  3. Alignment and headlight aim

Trail Boss on 35s

  1. Trail Boss-specific 3 in lift kit
  2. 35x11.5 tires
  3. 17x8.5 or 17x9 wheels, 5.5 in backspacing

ZR2 on 35s

  1. ZR2 kit that keeps DSSV, or AEV HighMark flares
  2. 35 in tires
  3. 17x8.5 wheels, about +12 offset

9. Frequently Asked Questions

How much lift does the Colorado Trail Boss have from the factory?

Chevrolet lists the Trail Boss with a 2 in factory lift and a front track about 3 in wider than the WT and LT.

How much lift does the Colorado ZR2 have?

The ZR2 has a 3 in factory lift and a wider stance, plus Multimatic DSSV dampers and front and rear electronic locking differentials.

Will a Trail Boss lift kit fit my Z71 or LT?

Usually not. Trail Boss kits we've checked state they fit only the Trail Boss and won't fit standard trims or the ZR2. Use a kit that lists your exact trim.

Can I lift a ZR2 and keep the DSSV shocks?

Yes. ZR2-specific spacer kits are designed to retain the factory Multimatic DSSV dampers while adding about 2 to 3.5 in of lift.

Do I need a lift for 35s on a ZR2?

Not necessarily. AEV's HighMark fender flares fit 35s on the 2023+ ZR2 with only a 1/2 in coil spacer and rear spring spacer, though the front fenders are cut during install. A ZR2 lift kit is the other common route.

Does the ZR2 Bison need a lift?

The Bison already comes on 35 in tires with AEV fender flares, so most owners don't need a lift for clearance. Make sure any kit lists the Bison specifically.

11. Sources & Technical References

Not sure which lift fits your Colorado? Call 419-670-3141 or email sales@offroadsource.info with your year, trim and tire goal.